FireGlass , fire glass, fire glass, fireplace, fire pit, modern fireplaces fire pits, https://www.moderustic.com
Moderustic Aquatic Glassel Fireplace Glass Rocks Propane FireplacesModerustic Aquatic Glassel Fireplace Glass Rocks Propane Fireplaces

Ed@Moderustic.com 909 989 6129

Page 2 Starfire Continued

 

The fire table below was built for Dr. Ramsey Burton in Kentucky. We are going to show you from beginning in the shop to the finished product that Ramsey envisioned for his patio. Ramsey did a wonderful job in planing, building and execution of this project. The glass he used was a Starfire Base Glass with Ice Ice Ice Topper on top. Here we go:
Fire Pit Pictures
Burton Fire Table 34
This was the lay out for the table to come!
Burton Fire Table 33
Burton Fire Table 32
these were the pictures we sent Ramsey after assembly and testing of the fire bowl, water pumps and fibre optics. The glass we tested with usually is our Multi Mix Base Glass. It tends to show off many colors and always looks great.
Burton Fire Table 31
Burton Fire Table 18
Above you can see the gas line and electrical
Burton Fire Table 19
Burton Fire Table 17
Access panel below.
Burton Fire Table 27
Below the bowl was fitted.
Burton Fire Table 28
Don't ever forget to install a trimming valve!
Burton Fire Table 20
Burton Fire Table 24
Burton Fire Table 23
Burton Fire Table 16
There are 6 colors on Ramsey's color wheel in the fibre optics.
Burton Fire Table 15
Burton Fire Table 14
Burton Fire Table 13
Burton Fire Table 10
Burton Fire Table 9
Burton Fire Table 8
Burton Fire Table 6
Burton Fire Table 5
Above and below you can see the cover Ramsey have made to protect the fire table when not in use.
Burton Fire Table 1
The fire pit below had the wrong type of burner let alone the location of the burner.
The burner must be with in 2" of the ultimate top of the surface of the fire pit. Filling the pit with gas and then trying to light it? Nothing good can become of this. We installed a #304 stainless steel "H" burner, covered it with crushed lava (1/4" / 3/8") over the larger lava rock. This is what keeps it from trickling to the bottom. Them we topped it with Starfire Base Glass. Then Eric is trying to decide which colors/ topper he should add if any at all. Fire Pit Pictures.
Eric Tufts 1
Eric Tufts 3
Eric Tufts 4
Eric Tufts 6
Wrong type of burner above.
Our "H" burner below. Watch the flame pattern as the crushed lava covers the burners.
Eric Tufts 7
Eric Tufts 8
Eric Tufts 9
Eric Tufts 10
Eric Tufts 11
Eric Tufts 12
Eric Tufts 13
Eric Tufts 14
Now for the big decision, more colors and which ones?
Eric Tufts 15




Las Vegas Yard Crashers!

This will air in April of 2010!

Here is a preview

Ahned Hassan

This is what was done on the first day. I showed up on the beginning of the second and the final day. It's amazing what can take place in just 12 hours!

Las Vegas Yard Crashers 1

Above the pavers were installed the day before.

Below is the patio with the outdoor kitchen set aside for now.

Las Vegas Yard Crashers 2

Las Vegas Yard Crashers 3

Las Vegas Yard Crashers 4

Above is where the outdoor kitchen will reside later.

Even the palm trees were brought in! There was nothing on the site when it started the day before.

Las Vegas Yard Crashers 5

Below Ahmed was leveling the ground around the fire pit area. Ahmed worked all day, much harder than anyone else! I was very impressed how hard he actually works to get the show done.

Las Vegas Yard Crashers 6

Las Vegas Yard Crashers 7

Below is where the propane fire pit will sit. The controller will be mounted to the side of the concrete base after the paper tubes are cut away.

Las Vegas Yard Crashers 8

Las Vegas Yard Crashers 9

Las Vegas Yard Crashers 10

Above and below you can see the inside of the planter is coated to prevent water from leaching out.

Las Vegas Yard Crashers 11

Above you can see on the ground that we brought the fire bowl in. Just so you know it was about 300 lbs!

Las Vegas Yard Crashers 12

Las Vegas Yard Crashers 13

Above and below you can see outdoor kitchen. The trough coming out is actually water fall spilling into a dry creek bed below. The water feature was covered with a glass top making it a dining area as well. On the inner wedges they wrapped rope lights to accent the water and rocks under the glass top.

Las Vegas Yard Crashers 14

Las Vegas Yard Crashers 15

Above and below you can see the sand was installed as a base for the artificial grass to come.

Las Vegas Yard Crashers 16

Las Vegas Yard Crashers 17

Above they are compacting the sand for the grass to be installed.

Below Ahmed is finishing the dry creek bed.

Las Vegas Yard Crashers 18

Below the grass is installed.

Las Vegas Yard Crashers 19

Below the dry creek bed is finished and the grass is now installed in the back are as well.

Las Vegas Yard Crashers 20

Las Vegas Yard Crashers 21

Fire Glass in a Fire Bowl

Above is our fire bowl on propane. We used Starfire Base Glass with Ice Ice Ice Topper and Diamonds on top. We brought out several colors of diamonds for the customer to pick and choose but she liked them all so much, she installed every last one!

Las Vegas Yard Crashers 22

Below you can see after everything was cleaned up how spectacular it turned out!

Las Vegas Yard Crashers 23

Las Vegas Yard Crashers 24

Las Vegas Yard Crashers 25

Las Vegas Yard Crashers 26a

Las Vegas Yard Crashers 27

Las Vegas Yard Crashers 28

We are to feature several more episodes with Yard Crashers and we will be showing several more of our new product lines on their shows.  We still have several shows we need to post pictures of what we did. Please come back from time to time to see our latest updates.

I thank Ahmed and the producers of the Yard Crashers for giving us the opportunity to work with them.

Thanks to Tiffany, Krystal and Holly at the Big Table Media!

Big Table Media produces Yard Crashers for the DIY Network

"Click HERE for the DIY Network/ Yard Crashers Site!"


The fireplace below belongs to Todd. As you are going to see one great before and after transformation. Now for the fireplace pictures!

He used an 1/8" Clear Base Glass with Starfire Base Glass on top. Then he added Red R Topper, Black Luster Topper and a few Clear Diamonds.

TODD SURLOFF 1

TODD SURLOFF 2

Out with the old and in with the new!

TODD SURLOFF 3

TODD SURLOFF 4

TODD SURLOFF 5

TODD SURLOFF 6

TODD SURLOFF 7

We would of liked more pictures of it burning but Oh Well!

TODD SURLOFF 8

 

Below is a collection we took pictures for our customer to decide on which base to use under the Amber Diamonds.

Amber Diamonds alone

AMBER DIAMONDS ALONE

Amber Diamonds on Black Base Glass

AMBER DIAMONDS ON BLACK

Amber Diamonds on Starfire Base Glass

AMBER DIAMONDS ON STARFIRE

Amber Diamonds on New Yellow Base Glass

AMBER DIAMONDS ON NEW YELLOW

Amber Diamonds on Bronze Base Glass

AMBER DIAMONDS ON BRONZE

The same product can be displayed thousands of ways. What do you want to see? Our diamonds are made with a convex base so when you look at the Diamonds in the fire they seem to be melting on the inside, like looking into a spoon. We cause it to reflect backwards. Visit out "Diamonds Page" to see many more colors!

 

 

The fire pit below is going to be installed in Sacramento on 11 14 09 for the Yard Crashers/ DIY/ HGTV show. After it is and has been installed we will post pictures on the Yard Crashers page. In the mean time here is the how to and why. We can build any size, shape, design feature you desire. We build to your imagination.

Below is the catch basin to hold the water for the feature

 

DIY PAN 1

Above you see the auto fill?

Below the water pump is now install below.

DIY PAN 2

Below the top pan is in place for testing with the fire and water bowls in place

DIY PAN 3

DIY PAN 4

Below the stainless steel ring is installed.

DIY PAN 5

Below the glass (Bronze Base Glass) has been installed and the lights turned on.

DIY PAN 8.

Below you can see the pump has been turned on.

DIY PAN 9

and now the fire.

DIY PAN 10

We placed a card board template to replicate the table top to conceal the lights as well.

DIY PAN 11

Now we add color to the water!

DIY PAN 12

DIY PAN 13

Here is the feature exposed with the blue water. You can change the water to any color you like.

DIY PAN 14

DIY PAN 15

This feature is only 6 1/2" tall. You can mount this under the table top and keep it only an inch or so above the surface of the table top.

DIY PAN 16

So let's change it to red water and add Starfire Base Glass.

DIY PAN 17

DIY PAN 18

DIY PAN 19

DIY PAN 20

DIY PAN 21

FireGlass on Water!

Remember, we build to your imagination!

DIY PAN 22

The finished pictures will be posted on the Yard Crashers page when this project is installed after 11 14 09!

 

Do it yourself fireplace remodel made easy, or at least it seems that way.

First, the tile that was installed is not rated for fire. This tile would of popped off as soon as the fire was turned on. So do a little research before you begin. We can help in many ways, just call and ask. Now for the fireplace pictures!

Christy's Fireplace 1

It may have of seemed to be a good idea at the time, but it wasn't!

Christy's Fireplace 2

When redesigning a fireplace we suggest card board mache'. A card board mock up so you can see a basic preview of your project.

Christy's Fireplace 3

Christy's Fireplace 4

Below you can see the bottom, top and mantle in card board.

Christy's Fireplace 5

Christy's Fireplace 6

Now the rip and tear process begins!

Christy's Fireplace 7

Below we installed the extra electrical for the components and the TV. The components will be installed on the right side out of view with a black glass door. This will be installed later.

Christy's Fireplace 8

Below the framing begins.

Christy's Fireplace 9

Christy's Fireplace 10

Below we now added the Durock at the fireplace opening. This is key to the whole project. Math is very important when doing these layouts!

Christy's Fireplace 11

Christy's Fireplace 12

Christy's Fireplace 13

Christy's Fireplace 14

Christy's Fireplace 15

Below you can see the slate is being added.

Christy's Fireplace 16

Christy's Fireplace 17

Christy's Fireplace 18

Christy's Fireplace 19

Above and below the fireplace is 90% finished. The mantle needs to be installed and the door on the right to conceal the components needs to be installed as well. The inside of the fireplace will have 3 pieces of black galaxy granite installed. We will post these pictures of the fireplace when it is completely finished as well.

Christy's Fireplace 20

Now for the glass installation. We started with a satin black paint on the back walls, until we install the granite.  Then we bulked up the base with 2" of white sand as this will save you a bunch of money! We used sand because we were pouring Starfire Base Glass in the fireplace. If we were to use a darker color of glass we would of used our crushed lava rock as a filler. When using sand, always make sure the burner is on top of the sand.

Christy's Fireplace 21

Test the burner/ location making sure the flames don't hit the walls.

Christy's Fireplace 22

Christy's Fireplace 23

Then pour the FireGlass!

Christy's Fireplace 24

Christy's Fireplace 25

We added a few Pink Diamonds and then later added Ice Ice Ice Topper and Clear Diamonds. These products because of the way they are made appear to be melting on the inside.

Christy's Fireplace 26

Cool Fire Glass!

Christy's Fireplace 27

Did you notice how we made it come out?

Christy's Fireplace 28

Christy's Fireplace 29

The sealer that was used was a stone enhancer, not just a regular cheap sealer. When using rock you always want to see the beauty of the stone you are using.

Christy's Fireplace 30

Christy's Fireplace 31

Christy's Fireplace 32

As you can see the mantle is still missing. We have a few more details to still do and as soon as we have time to post the pictures, they will be here.

We encourage imagination to all of our customers and we support you and your projects. Regardless how simple or how creative. This is one of the elements that spawned our success and continues to do so.

 

Kentucky Fireplace Remodel

The next fireplace was built by Dave Luerman in Kentucky and you will now see his before and after also using a base of Starfire Base Glass.

Below you can see where it all began. Dave is one very creative customer.

Luerman 1

The fireplace that was replaced was very nice but just met the needs of Dave.

Luerman 2

Out with the old and lets frame up the new.

Luerman 3

Luerman 4

Luerman 5

Add the durock panels.

Luerman 6

Luerman 7

Luerman 8

Frame the Hearth

Luerman 11

Luerman 10

Luerman 12

Install a triple 24" burner.

Luerman 13

Luerman 14

Luerman 15

Luerman 16

Luerman 17

Luerman 18

Add Starfire Base Glass and you are done.

Luerman 19


The fireplace below is from Steve Calderon and he used a Starfire Base Glass with Gold Base Glass and Bronze Rust Copper Base Glass on top.

This is from beginning to end.

Calderon 1

Above is the before believe it or not. As you can see Steve did a terrific job. This was a wood burning fireplace before. he installed a gas line and control valve on the right side.

Calderon 2

Calderon 3

Below you can see the old burner which we replaced with the new double 18" burner.

Calderon 4

Calderon 5

Calderon 6

Calderon 7

Mask it, vacuum it after wire brushing the walls clean.

Calderon 8

Calderon 9

A bit of Thermolux 1200 degree high heat paint.

Calderon 10

Fireplace Glass used:

Pour in a Starfire Base Glass with a splash of Gold Base Glass and Bronze Rust Copper Base Glass on top.

Calderon 11

Calderon 12

.Calderon 13

Calderon 14

Then you have one nice fireplace, great job!

Calderon 15


The fireplace below had a few issues, but easily repaired. Be sure to not let this happen to you! If anyone tries this type of installation, stop them and throw them out!  This fireplace installation was in Palm Springs California. It was done with the 2" method which is fine except for the burner the fireplace shop installed. We will explain as we move forward and show you the finished fireplace.

Below is what we saw when we arrived.

Palm Springs 4

Then we tested the burner we were to replace, oh my!

Palm Springs 5

We uncovered to see what was installed and found a single pipe burner. Great Flame! Another issue was the paint job was hideous which was later repainted. Don't let these ignorant installer tell you their stories. They told the customer the paint would dry to match.

Palm Springs 1

We do approve of a sand filler indoors under lighter colored glass, but the burner must be on top!

Palm Springs 2

Palm Springs 3

Now we installed a double burner and just watch!

Palm Springs 6

Below is what they pawned off on the customer, DON'T LET THIS HAPPEN TO YOU!

Palm Springs 7

Palm Springs 8

Much better. Then we took several pictures of the fireplace just because! We did top it off with about 15 lbs of Starfire Base Glass to help hide the sand that was exposed and it worked out just fine.

Palm Springs 9

Palm Springs 10

Palm Springs 11

Palm Springs 12

Palm Springs 13

Palm Springs 15

Palm Springs 16

Palm Springs 17

 

The next fireplace were installed in Malibu California. The master bedroom was on the third floor. We did a little paparazzi photo shoot while we were there. The glass we installed was 1/4" Starfire Base Glass.

Malibu 7

Malibu 6

Malibu 5

Malibu 8


The fireplace below is in Beverly Hills California. We used a Starfire Base Glass with Clear Diamonds and Black Luster Topper.

Rosen 7

Rosen 8

Rosen 9

Rosen 10

 

 

                                   

The fireplace below had a steel pan built so we could conceal the 12 volt battery operated electronic ignition

beneath the pan. The glass that was installed was:

Jim Malless 1
Jim Malless 2
Jim Malless 3
Above and below you can see the solid cover as it hangs over the face to conceal the remote control ignition.
Jim Malless 4

Jim Malless 5

 

The fireplace below is in Palm Springs California. We used Starfire Base Glass over a 2"
 bed of sand. We will narrate as we go:

Here is the fireplace with the screen removed

Palm  Springs Install 1

Palm  Springs Install 2

Now we remove the doors, very simple. One screw on each side at the top generally removes the doors.

Palm  Springs Install 3

Below, remove the end of the flex line and screw it on to the stub out coming out of the wall.

Palm  Springs Install 4

Below, now attach the flex line from the burner to the stub out. Keeping the flex line curled under the burner.

Palm Springs Install 5

Below, pour in as much sand (on lighter colors) as you would like to raise the glass bed.

Palm  Springs Install 6

Look how easy! Even my installers can do it! Bring the burner to the top of the sand so it can operate properly. With crushed lava you can keep the burner below the surface. Keep your sand/ lava at least 3" to 4" away from the front!

Palm  Springs Install 7

Pour the glass and you are done! Our typical install where we don't have to paint is about 12 minutes!

Palm  Springs Install 8

Palm Springs Install 9

Palm Springs Install 10

Looks awesome!

Palm  Springs Install 11

 

                                                                                                                                                   

The 2 fireplaces below are

 Claremont California.

We installed Starfire Base Glass in each of them and then the customer ordered Ice Ice Ice Topper and Diamonds to accent each fireplace.  Very nice stone work!
Claremont 1
This is the living room fireplace and we poured about 3" of sand under the Starfire Base Glass. We used a 44" "H" burner under the Starfire Base Glass.
Claremont 2
Claremont 3
Claremont 4
Claremont 5
Claremont 6
Claremont 7
Claremont 8
Claremont 9
The family room fireplace was filled with about 8" of sand under the Starfire Base Glass. We installed a 38" "H" burner on top of the sand.
Claremont 10
Claremont 11

Claremont 12

 

                                                                                                                                                     

The fire pit below was purchased locally and then we converted it to burn propane without soot! The colors used were:

Starfire Base Glass,

and topped with 1 lb of Copper Ruby Red Topper. I guess he wanted a lot of color.

 

James 2
Here is what is looked like when he started. These manufactures have no imagination!
James 3
James 4
This only cost about $100.00, complete!

James 1FireGlass, Aquatic Glassel

 

The fireplace below is typical wood burning fireplace which we see every day. Once uncovered it looks like an incinerator. They are pretty nasty looking with out the fire burning. We like to show the before and after so you know what you really have.

Steve 1

Nice! Very Nice!

Steve 2

We had Starfire Base Glass installed with Ice Ice Ice Topper on top.

Steve 3

Steve 4

Steve 5

Steve 6

 

This next fireplace was done with lack of knowledge! First they installed a 18" single burner and some real interesting choices of glass. What they did do correct is have a 3" sand bed under their yuk glass. The first issue we repaired was the stub out on the left side of the fireplace floor. All we did was install a 90 degree elbow and connect a 1/2" flex line to the new double 24" burner. They had left the flex pointing in the air and then reduced it to a 3/8" line and to top that off added they very sad single 18" burner. We repainted their futile attempt (of painting) with dark metallic brown, added 10 lbs of sand and poured 75 lbs of Starfire Base Glass over the new burner and sand filler. We will explain as we move forward:

PS Convert 1

PS Convert 2

Below you can see the black marks under the paint.

PS Convert 3

Below you can see the flex line that was installed was left above the surface. Now if we tried that I think our customers would take us out and string us up, what do you think? To top it off this customer was an attorney! Completely happy with what we did.

PS Convert 4

Here is the new paint on the back walls.

PS Convert 5

Now we added the Starfire Base Glass. One thing we have been doing a little bit different is to bring the glass out from the front of the fireplace. We let the glass come out of the fireplace from 3 to 6 inches to make it look even more grand. What do you think?

PS Convert 6

PS Convert 7

PS Convert 8

Here is a the almost finished product of what we do! We left several colors with the customer to add. We will post pictures when they arrive.

PS Convert 9

Below are the finished pictures of what else was added:

Yellow Amber Topper,

Ice Ice Ice Topper,

Clear Diamonds,

Fuchsia Topper,

Purple Topper,

Red R Topper,

Roma Red Topper

I think it turned out very colorful! Check it out!

Joan Sklar 1

Joan Sklar 2

Joan Sklar 3

Joan Sklar 4

Joan Sklar 5

Joan Sklar 6


Just when I thought they couldn't do something different, they did! I agree with the sand as a base under the Starfire Base Glass. I will explain as we go forward:Paul 1

I finally understood the weird brackets, he was calculating the height of his burner for sand filler underneath.

Paul 5

Above and below I understand testing the burner.

Paul 6

Paul 7

OK, I give, he taped the holes to prevent sand from getting in the burner. That doesn't really matter as too much sand really can't get inside and if it does, no big deal.

Paul 2

Paul 3

Paul 4

What I don't understand is the burner left on top of the glass. Didn't I show enough pictures for you to get the hint? No really? I guess he missed those few hundred pages of pictures.

Paul 8

Paul 9

Paul 10

Paul 11

Paul 12

If this is the look he was after, then he got it! Different strokes for different folks.

Paul 13

 

The fireplace below is a self installation by Thom Toben of Studio T2 Designs in Kansas. & colors were installed and they are;

Clear Base Glass with Starfire Base Glass mixed together over

Medium Amber Topping

Bronze Rust Copper Base Glass

Black Luster Topper

Yellow Amber Topper and

Turquoise Blue Topper

You be the judge, we think it looks great!

Thom Toben 6

Below the burner is installed with the flex line under the burner

Thom Toben 4

Now the lava goes in and the burner is brought up to the surface

Thom Toben 5

Test the burner to insure the flame don't hit the back wall.

Thom Toben 2

The Clear Base Glass and Starfire Base Glass was poured on top of the lava.

Thom Toben 7

Then Thom placed all of the other selected to match the room.

Thom Toben 1

Thom Toben 9

Thom Toben 8

Thom Toben 9

Thom Toben 3

 

The next fireplace was featured in MILWAUKEE, www.GMToday.com

Simply perfect
Contemporary in the country is a way to enjoy the best of both worlds

The family’s theater room takes on a contemporary flare with a stainless steel-tiled fireplace. Shards of glass replace artificial embers in the gas fireplace, creating a glow as the flames flicker. A large screen on a remote control is located above the fireplace, perfect for the family to watch a movie together.

GMTodayPicture by Doug Edmunds

"Click Here for the full article!"


The fire pit below was installed in Sydney, Australia by Ian Sutherland. He did a great job on his new patio and fire pit. We inspired him to build this really nice back yard project and we were glad to help. The glass that was used was Azurlite Base Glass and Starfire Base Glass.

Australia 11
Australia 11FireGlass down under!
Australia 10
Australia 8
Australia 6
Australia 5
Australia 3
Australia 2

Australia 1

 

The picture of the fire pit below was taken in Newport Beach California. The glass that was installed was Starfire Base Glass. One very nice backyard and fire pit!

Rhonda 1

 

The next several fireplace pictures are from Andy Peeke from New Jersey.  Andy did the self installation with his wife. Almost a complete fireplace make over once you see. They use a Starfire Base Glass, Amber Topper and Black Topper.

Andy Peeke 10

The house is very nice, the fireplace right now is "YUK"!

Andy Peeke 9

YUK again!

Andy Peeke 8

Andy Peeke 1

We used a double "H" to give a wider flame pattern as you will see.

 

Andy Peeke 2

We also used a sand base under the Starfire Base Glass and just up to the burners, not covering them.

Just so you know, this is a two sided fireplace.

Andy Peeke 3

Now 2" of Starfire Base Glass.

Andy Peeke 4

and you are done!

Andy Peeke 5

Andy Peeke 6

Andy Peeke 7

 

The fireplace pictures below show the before and after from Bob Kobus. The glass that was used is:
Starfire Base Glass and Ice Ice Ice Topper, Very nice, contemporary and simple!
Let's go from start to finish:
Bob Kobus 1
Nice Logs! NOT!
Bob Kobus 2
Bob used an aluminum brick metalized panel.
Bob Kobus 6
Then they did their grind pattern.
Bob Kobus 7
And here you have it finished!
Bob Kobus 4
Bob Kobus 5
Yes the logs will be leaving very soon!
Bob Kobus 8
Bob Kobus 9
Bob Kobus 10
Much better, don't you think?
Bob Kobus 11
                  

The fireplace pictures below will show how simple and easy it actually is to install.

Here are a few comments from J.D. Hariman

  John. Harriman@dlapiper.com

Subject:  More proof of how easy it is to do with Moderustic providing the materials!


 We are so happy with our FireGlass fireplaces (we have 3!).  It has literally changed our lives in that we can use our fireplaces anytime we want with no worry about
cleaning ashes later on.  Even better, the look is so superior to fake logs.  All of our friends have been wowed by the look.  We always send them your way.
 
Best regards,
 
J. D. Harriman

Here we go:

001

Above you can see how nice it WAS! YUK!

Below they painted, we always recommend painting the lines first and then painting each brick separately. Using this technique you can eliminate spots.

002

Install the burner. We usually recommend curling the flex line from underneath, but this works as well if your flex line is long enough. The reason for the flex line: it allows you to move the burner forward to prevent the flames from hitting the back wall.

003

Below the lava has been poured and test the flame pattern.

004

Pour the glass from the front going to the back. You can use a cup or pour from the bucket.

005

Turn it on and you are done!

006

The glass that was used is:

Starfire Base Glass,

1 lb of Gold Base Glass,

Amber Diamonds,

Ice Ice Ice Topper for one simple but nice fireplace!

007

 

The before and after pictures below are of a Starfire Base Glass and Clear Diamonds.
Starfire and  Diamonds 2
Starfire and  Diamonds 1

 

Scott Sanders drilled a hole in his patio table and attached the propane to the RV fire pit from the bottom. He can take it when he want anywhere by the use of a quick disconnect gas line to his tank.

Scott Sanders  Pit 2

Scott Sanders Pit 1

 

John Kirkhan below started with a Starfire Base Glass and added:
John Kirkhan 1




Direct Vent Conversions! (Direct Vent page)

Yes these can and able to be converted!

How to make "THIS"

(Click below to see how we did this!)

Joe Yuga Direct Vent

Into "THIS"

Joe Yuga Direct Vent

______________________________________________________________________

Click HERE or on the picture to see how it was transformed to this!

Steve Clendenen

From THIS! (BELOW) again YUK!

Steve Clendenen


_____________________________________________________________________

CLICK HERE or on the PICTURES below to see how this became what it is today!

Palm Springs Indoor Fire Pit

Palm Springs Indoor Fire Pit
_____________________________________________________________________



____________________________________________________________________________________

From here:

From nasty to BEAUTIFUL in an hour!

Palm Desert Swoop Mirrors

To here:

Palm Desert Swoop Mirrors
______________________________________________________________________________

______________________________________________________________________

_______________________________________________________________________________
This Surround was a challenge, as the top and bottom were not square, the top center was 2 1/2" and the bottom was 2". Anyway, after it was installed, it looked awesome!

(Click on the PICTURE)

Barry DeBreau Corner Surround

We built a custom size steel pan to go into the fireplace with Starfire Base Glass installed

There is 4" of Black frame all around, 4" of black glass on the sides and 4" of black glass on the top.

The Black Paint we used was Satin Black Silicone based fireplace paint. Do not use regular paint, no really.

Barry DeBreau Corner Surround

Click on the Pictures or HERE to see the rest of the Surround Pictures
____________________________________________________________________________________

 

_________________________________________________________________________

Click HERE or on the picture below to see how this was installed!

Rosanne Rosanne Bandana Surround Mantle
And what was used

_________________________________________________________________________



Additional Links for Starfire.

1/4" Starfire Pictures

More 1/4" Starfire Pictures

1/2" Starfire Pictures

1/8" Starfire Pictures

More 1/8" Starfire Pictures

3/4" Starfire Pictures

1/4" Starfire Pictures

More 1/4" Starfire Pictures

Starfire Pictures

 

1/4” Starfire “CLICK HERE TO SEE THIS PRODUCT IN THE E STORE!”

Ed@Moderustic.com 909-989-6129

9467 9th street Unit D

Rancho Cucamongs, California 91730

 

Our Glass is SAFE and See Why!

Safe Glass
 We  Appreciate Your Comments & Feed Back. Please
Send Your E-mails or Click HERE to Submit a Survey!



909-989-6129  Fax: 909-944-3811 
or E-mail us at
Ed@Moderustic.com |  Jaunzemis@msn.com  

Ed@Moderustic.com 909-989-6129

9467 9th street Unit D

Rancho Cucamongs, California 91730


 
Moderustic Aquatic Glassel Fireplace Glass Rocks Propane Fireplaces